Data Table
|
Normal
|
With Fan
|
With Heater
|
With Lamp
|
Arrowhead
|
3.6
|
7.5
|
6.6
|
4.0
|
Coleus
|
0.9
|
6.0
|
3.9
|
3.0
|
Devil’s Ivy
|
2.9
|
4.6
|
4.1
|
3.0
|
Dieffenbachia
|
4.1
|
7.7
|
6.0
|
3.9
|
English Ivy
|
1.8
|
5.1
|
3.2
|
2.1
|
Geranium
|
1.2
|
4.7
|
5.8
|
2.4
|
Rubber plant
|
4.9
|
8.4
|
6.8
|
4.3
|
Weeping Fig
|
3.3
|
6.1
|
4.9
|
2.5
|
Zebra Plant
|
4.2
|
7.6
|
6.1
|
3.2
|
Arrowhead: 7.5-3.6 = +3.9
Coleus: 6.0-0.9 = +5.1
Devil's Ivy: 4.6-2.9 = +1.7
Dieffenbachia: 7.7-4.1 =
Rubber Plant: 8.4-4.9 = +3.5
Weeping Fig: 6.1-3.3 = +2.8
Zebra Plant: 7.6-4.2 = +3.4
Average: +3.42 (The wind had a positive effect, increasing the average transpiration rate of the plants by 3.42)
The numerical effect of the heat (heater)
Arrowhead: 6.6-3.6 = +3.0
Coleus: 3.9-0.9 = +3.0
Devil's Ivy: 4.1-2.9 = +1.2
Dieffenbachia: 6.0-4.1 = +1.9
English Ivy: 3.2-1.8 = +1.4
Geranium: 5.8-1.2 = +4.6
Rubber Plant: 6.8-4.9 = +1.9
Weeping Fig: 4.9-3.3 = +1.6
Zebra Plant: 6.1-4.2 = +1.9
Average: +2.28 (The wind had a positive effect, increasing the average transpiration rate of the plants by 2.28)
The numerical effect of light (lamp)
Arrowhead: 4.0-3.6 = +0.4
Coleus: 3.0-0.9 = +2.1
Devil's Ivy: 3.0-2.9 = +0.1
Dieffenbachia: 3.9-4.1= -0.2
English Ivy: 2.1-1.8 = +0.3
Geranium: 2.4-1.2 = +1.2
Rubber Plant: 4.3-4.9 = -0.6
Weeping Fig: 2.5-3.3 = -0.8
Zebra Plant: 3.2-4.2 = -1.0
Average: +0.17 (the light had a marginal positive effect, increasing the average transpiration rate of the plants by 0.17)
Therefore, the wind, followed by heat and light, had the biggest impact on the plants' transpiration rate.
1.
Describe the process of
transpiration in vascular plants.
In vascular plants, water is absorbed through the roots and carried
upward through the stem to the leaves. Some of the water absorbed by a plant's
roots is used for photosynthesis, but much is lost to the environment by
evaporation through stomata. This process
is called transpiration.
2.
Describe any experimental
controls used in the Investigation.
In a laboratory, a plant's transpiration rate can be measured using
a potometer.
To measure transpiration rate, a plant sprig is mounted on the
potometer and the burette and pipette are filled with water. Over time the
plant will transpire and absorb water through its stem. The potometer is
constructed in such a way that the plant's water source is the pipette,
therefore the amount of water transpired over time can be determined by reading
the water level in the pipette after time has passed. The water supply in the pipette
can be replenished from the water supply in the burette by releasing the pinch
clamp.
3.
What environmental factors that
you tested increased the rate of transpiration? Was the rate of transpiration
increased for all plants tested?
Wind and heat increased the rate of transpiration for all plants
tested.
Light, however, increased the transpiration rate for some plants,
and decreased the rate for others.
4.
Did any of the environmental
factors (heat, light, or wind) increase the transpiration rate more than the
others? Why?
Wind increased the transpiration rate more than heat and light did.
This is somewhat related to the relative
humidity of the air, in that as water transpires from a leaf, the water
saturates the air surrounding the leaf. If there is no wind, the air around the
leaf may not move very much, raising the humidity of the air around the leaf.
Wind will move the air around, with the result that the more saturated air
close to the leaf is replaced by drier air.
5.
Which species of plants that
you tested had the highest transpiration rates? Why do you think different
species of plants transpire at different rates?
Rubber plant showed the highest transpiration rate. This is
primarily due to its leaves with a bigger surface area. Varying transpiration
rates according to different species are the result of adaptation to climate. Some plants which grow in arid regions,
such as cacti and succulents, conserve precious water by transpiring less water
than other plants.
6.
Suppose you coated the leaves
of a plant with petroleum jelly. How would the plant's rate of transpiration be
affected?
As petroleum jelly tends to hinder water from evaporating, the
transpiration rate will drop abruptly.
7.
Of what value to a plant is the
ability to lose water through transpiration?
Transpiration cools plants, changes osmotic
pressure of cells,
and enables mass flow of mineral nutrients and water from roots to shoots.